Skip to content

Tile installation

1/8 vs 1/16 grout line: how narrow can a Florida tile floor go?

How the tile itself sets the narrowest grout joint, when a 1/16 inch line works, why 1/8 inch is the usual answer, and what changes for wood-look planks and 12x24 tile.

Updated November 15, 2026

Showroom aisle lined with black racks of hexagon, encaustic and colored brick-look wall tiles

For most tile floors the answer to 1/8 vs 1/16 grout line is 1/8 inch. A 1/16 inch joint is the narrowest the tile standard allows at all, and only tile that is very even in size and very flat, laid on a floor flattened to match, can take it without the lines wandering or the edges catching the light.

So the width is not really a matter of taste. The tile in the boxes decides how narrow the joint can go, and the floor under it decides whether a narrow joint will look clean or show every step. Here is how that works, and how to tell which of the two widths your tile can carry.

What decides the minimum grout line width?

The tile installation standard most of the trade works to, ANSI A108.02, ties the joint to the tile rather than to the design. The joint should be at least three times the actual variation in face size across the tile supplied for the job, and never less than 1/16 inch. Its own example: tile that varies by 1/16 inch in size needs a joint of at least 3/16 inch. The Ceramic Tile Education Foundation explains why the standard sizes the joint this way.

The reason is simple once you picture it. Every tile from a kiln comes out a fraction bigger or smaller than its neighbours. The joint is where that difference goes. If the joint is too narrow to absorb it, the installer has a choice between keeping the joints even and letting the lines drift across the room, or keeping the lines straight and letting the joints vary in width. Neither looks like the drawing.

That is why a joint width belongs to a particular tile and a particular delivery, not to tile in general. Two lines with the same nominal size can need different joints, because one is held to a tighter tolerance at the factory than the other.

When does a 1/16 grout line actually work?

A 1/16 inch joint needs three things to line up, and missing any one of them is enough to rule it out.

  • The tile is rectified: its edges ground square after firing, so the pieces in the box are all but identical in size. A pressed edge varies too much for a joint this narrow.
  • The face is flat. Rectifying squares the edges but leaves any bow in the face where it was, and a narrow joint has no room to hide one edge sitting higher than the next.
  • The floor is flat. Most floors here are a concrete slab, and a slab is rarely as flat as it looks. It has to be measured and levelled where it needs it before any tile goes down.

There is a fourth, smaller point: the grout itself. Sanded cement grout is made for wider joints, and the sand will not pack into a joint this thin. Narrow joints take an unsanded grout or one sold for narrow joints, so check the joint range printed on the bag before the grout is ordered.

If you are unsure what the edge on your tile is, what rectified tile is explains the difference between a ground edge and a pressed one, and why a crisp edge shows a height difference more than a soft one does.

Why is 1/8 inch the usual answer?

Because it gives the joint room to work. At 1/8 inch, a rectified porcelain absorbs its normal size variation with the lines still straight, a slight bow in the face is less obvious, and the grout has enough body to fill and finish cleanly. It still reads as a fine line from standing height, especially with a grout colour matched to the tile.

For porcelain tile in the wood, stone and concrete looks, 1/8 inch is where most layouts start, and the conversation is about whether this tile, on this floor, can go narrower. A pressed-edge tile, a handmade look or a tumbled stone usually goes the other way, wider than 1/8 inch, because the variation is part of the character.

A narrower joint also does less than people expect. The difference between 1/8 and 1/16 inch is hard to see from across a room. What you do see from across a room is a line that drifts, a joint that changes width, or a shadow along one raised edge, and those are the risks a joint that is too narrow for the tile brings with it.

1/8 vs 1/16 grout line on wood-look tile

Wood-look plank tile is where a 1/16 inch joint is most tempting, because the real floor it imitates has no grout at all. It is also where it is hardest to get away with. A long, narrow plank shows any bow along its length, and the standard has a separate joint rule for long tiles laid in a stagger.

Children's bunk room with built-in light oak bunk beds over a dark wood-look plank tile floor

When long tiles go down in a running bond, the brick-style stagger most plank floors use, ANSI A108.02 asks for an average joint of at least 1/8 inch even with a rectified edge, and wider again for any warp. It also limits the stagger on long tiles to a third of their length unless the maker says otherwise, so the high end of one plank does not sit against the low middle of the next. Editions of the standard differ on exactly where a tile counts as long, but a plank of three or four feet is long under all of them.

So on most wood-look plank floors the honest answer is 1/8 inch, with a grout picked from the darker tones of the grain so the joint sinks into the pattern. A 1/16 inch joint on a long plank asks the tile and the slab for more than most deliveries can give.

What size grout line for 12x24 and 24x24 tile?

A 12x24 tile has a 24 inch side, long enough under every edition of the standard that a running bond brings in the 1/8 inch average minimum, even when the tile is rectified. In a straight grid, a rectified 12x24 is usually laid at 1/8 inch too, and anything narrower is a question for the tile maker's own recommendation and the measured variation of the delivery.

A 24x24 tile is a long tile under the standard too, so 1/8 inch is the safe place to start. A narrower joint is only worth discussing for a very consistent rectified tile in a straight grid, with the tile maker's recommendation in hand, and even then a big square shows a dip in the slab as a raised corner, so the flatness of the floor tends to decide it. At 24 inches and above the tile goes to our large-format installers, where a mechanical levelling system holds the edges in plane while the mortar cures.

Does a narrower grout line mean less cleaning?

A little, but less than the joint width suggests. What makes grout hard to keep clean is how much water and dirt it takes in, not how wide it is. A cement grout in a 1/16 inch joint still darkens in the traffic path if it is porous, while a dense grout in a 1/8 inch joint wipes clean.

If a clean joint matters more to you than a narrow one, the grout type is the bigger decision. Epoxy grout vs cement grout covers what each one does on a floor and in a shower, and whether either suits a narrow joint is a question for the grout maker's range.

Where the joint is not grout at all

Not every joint on a tile floor is a grout line. Where the floor meets a wall, at a change of plane and where the slab calls for it, the tile stops short and the gap is filled with a flexible sealant instead of grout, because a slab moves with the seasons and grout run tight to the wall has nowhere to go. Those joints are planned with the layout, and the sealant comes in colours made to go with the grout.

If you want almost no joints

Past a certain point the way to fewer, finer lines is not a narrower joint but a bigger piece. Large-format porcelain panels run from 48 inches up to 126 inches, so a wall or floor that would take a grid of tiles takes a handful of joints. With an edge that long, the flatness work under the panel is a different trade from tile, which is why it has its own crew.

How to choose the joint before you order

Decide the joint with the tile, not before it. In the Bradenton showroom the porcelain stands upright at full size, and we finalize grout, layout and edge details with the tile in front of you, so the joint width is chosen as drawn rather than guessed. The width, the grout, the offset and the floor preparation then go on one proposal for tile installation, because we sell it and we install it.

Call (941) 253-0400, or send us your plans for a quote and we will tell you which joint the tile you have in mind can carry.

Common questions

Should wood-look tile have a 1/8 or a 1/16 grout line?

Usually 1/8 inch. A wood-look plank is a long tile, and when it is laid in a staggered pattern the ANSI A108.02 standard asks for an average joint of at least 1/8 inch even with a rectified edge, wider for any warp. A long plank also shows any bow along its length, which a 1/16 inch joint cannot hide. A grout picked from the darker tones of the grain helps the joint disappear.

What size grout line for 12x24 tile?

For a rectified 12x24 tile, 1/8 inch is the usual answer. Its 24 inch side is long enough that in a running bond the standard asks for an average joint of at least 1/8 inch. In a straight grid it can go narrower only if the tile maker allows it, the tiles in the delivery vary very little in size and the floor is flat. A pressed-edge 12x24 generally needs a wider joint.

What size grout line for 24x24 tile?

Start from 1/8 inch for a rectified 24x24 tile, and go narrower only if the tile maker recommends it and the tiles vary very little. The standard asks for a joint at least three times the tile's actual size variation, and never under 1/16 inch. On a big square the flatness of the floor usually decides it, because a dip in the slab shows as a raised corner at the joint.

Is a 1/16 grout line too small?

Not if the tile and the floor can carry it, and often yes if they cannot. It is the narrowest joint the tile standard allows. It needs a rectified tile with very little size variation, a flat face, a floor flattened to match, and a grout made for narrow joints. Without all four, the lines drift or the edges show, which looks worse than a slightly wider joint.

Visit the showroom

Two buildings, one parking lot.

4.9
65 Google reviews

Address

6823 14th St W
Bradenton, FL 34207

Hours

Monday – Friday
8.30am – 5pm
Saturday – Sunday
Closed